CISCO AUX BACK-TO-BACK 实例

2013-11-5不详中国IT实…

  Click on the routers in the topology below to vIEw their configurations.
  
  router 2500 AUX----NULL MODEN CABLE-----ROUTER 2500 AUX
  
  Before You Begin
  This configuration has Cisco 2500-serIEs routers back-to-back using the async AUX port. The Cisco AUX port is connected to another CiSCo AUX port running PPP. The connection has been configured to allow IP for a permanent connection.
  
  IngredIEnts
  For this recipe, you need the following:
  
  A null modem cable.
  
  You may also need an RJ45-to-DB25 adapter converter. For more information on cables, see the Cables documentation.
  
  Router 1
  version 11.1
  service udp-small-servers
  service tcp-small-servers
  !
  hostname Router1
  !
  interface Ethernet0
  no ip address
  shutdown
  !
  interface Serial0
  no ip address
  shutdown
  !
  interface Serial1
  no ip address
  shutdown
  !
  interface Async1
  ip address 192.168.10.1 255.255.255.0
  ! -- the IP address on the AUX ports of both routers must be in the same subnet
  encapsulation ppp
  ! -- set PPP as encapsulation
  async dynamic routing
  async mode dedicated
  !
  no ip classless
  ip route 0.0.0.0 0.0.0.0 Async1
  logging buffered
  !
  line con 0
  exec-timeout 0 0
  line aux 0
  modem InOut
  transport input all
  rxspeed 38400
  txspeed 38400
  flowcontrol hardware
  line vty 0 4
  login
  !
  end
  
  Router 2
  version 11.1
  service udp-small-servers
  service tcp-small-servers
  !
  hostname Router2
  !
  !
  interface Ethernet0
  no ip address
  shutdown
  !
  interface Serial0
  no ip address
  shutdown
  !
  interface Serial1
  no ip address
  shutdown
  !
  interface Async1
  ip address 192.168.10.2 255.255.255.0
  ! -- the IP address on the AUX ports of both routers must be in the same subnet
  encapsulation ppp
  async dynamic routing
  async mode dedicated
  !
  no ip classless
  ip route 0.0.0.0 0.0.0.0 Async1
  logging buffered
  !
  line con 0
  exec-timeout 0 0
  line aux 0
  modem InOut
  transport input all
  rxspeed 38400
  txspeed 38400
  flowcontrol hardware
  line vty 0 4
  login
  !
  end
  
  Debug and Show Commands to Use for Troubleshooting
  Check under line aux 0:
  Issue the show line aux 0 command.
  
  Verify that all signals are up. For example, CTS, RTS, DTR, CD. If nothing appears next to them, they are up. If "No" appears next to them (for example, No-CTS), it means they are down.
  Router1#show line aux 0
  Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns
  A 1 AUX 38400/38400 - inout - - - 0 0 0/0
  
  Line 1, Location: "", Type: ""
  Length: 24 lines, Width: 80 columns
  Baud rate (TX/RX) is 38400/38400, no parity, 2 stopbits, 8 databits
  Status: Ready, Active, Async Interface Active
  CapabilitIEs: Hardware Flowcontrol In, Hardware Flowcontrol Out
  Modem Callout, Modem RI is CD, Line is permanent async interface
  Modem state: Ready
  Special Chars: Escape Hold Stop Start DiSConnect Activation
  ^^x none - - none
  Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch
  00:10:00 nEVEr none not set
  Modem type is unknown.
  Session limit is not set.
  Time since activation: 00:00:30
  Editing is enabled.
  History is enabled, history size is 10.
  Full user help is disabled
  Allowed transports are pad v120 telnet. Preferred is telnet.
  No output characters are padded
  No special data dispatching characters
  Line is running PPP for address 192.168.10.2.
  0 output packets queued, 1 input packets.
  Async ESCape map is 00000000000000000101000000000000
  Modem hardware state: CTS* DSR* DTR RTS
  Use the show line command to determine the async interface of the AUX ports. Though most routers have the AUX port as interface async 1, Access servers have the AUX port interface after the tty lines. For example, if your router has 16 async/modem lines, then the AUX port is line 17. In this case, the AUX port must be configured on interface async 17. Configure the AUX port based on the show line outputs. The example below verifIEs that the AUX port is on int async 1.
  
  Router1#show line
  Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns
  * 0 CTY - - - - - 0 0 0/0
  A 1 AUX 38400/38400 - inout - - - 0 0 0/0
  2 VTY - - - - - 0 0 0/0
  3 VTY - - - - - 0 0 0/0
  4 VTY - - - - - 0 0 0/0
  5 VTY - - - - - 0 0 0/0
  6 VTY - - - - - 0 0 0/0
  Use these debug commands to verify that the link comes up correctly:
  
  debug ppp negotiation - To display information on PPP traffic and exchanges while negotiating Link Control Protocol (LCP), Authentication, and Network Control Protocol (NCP). A successful PPP negotiation will first open the LCP state, then Authenticate, and finally negotiate NCP. If CONFREQs are being sent out, but no CONFACKs being received, check that the cabling is correct and whether the correct line (interface async x) is configured.
  debug ppp authentication - To display PPP authentication protocol messages, including Challenge Handshake Authentication Protocol (CHAP) packet exchanges and Password Authentication Protocol (PAP) exchanges.
  debug ppp error - To display protocol errors and error statistics associated with PPP connection negotiation and operation.
  Before attempting any of the above debug commands, please see Important Information on Debug Commands.

本文来源:不详 作者:中国IT实…

聚合推荐
声明
声明:本站所发表的文章、评论及图片仅代表作者本人观点,与本站立场无关。若文章侵犯了您的相关权益,请及时与我们联系,我们会及时处理,感谢您对本站的支持!联系Email:support@txwb.com,系统开号,技术支持,服务联系QQ:1175525021本站所有有注明来源为天下网吧或天下网吧论坛的原创作品,各位转载时请注明来源链接!
天下网吧·网吧天下